Pass Fortinet NSE6_FWF-6.4 Exam with Guarantee Updated 37 Questions
Latest NSE6_FWF-6.4 Pass Guaranteed Exam Dumps Certification Sample Questions
Fortinet NSE6_FWF-6.4 certification exam covers a wide range of topics related to secure wireless LAN technology, including wireless LAN security fundamentals, wireless LAN deployment best practices, wireless LAN troubleshooting, and wireless LAN management. Candidates who successfully pass this certification exam are recognized as experts in the field of secure wireless LAN technology and are able to demonstrate their knowledge and skills to potential employers.
NEW QUESTION # 16
A tunnel mode SSID is configured on a FortiGate wireless controller.
Which task must be completed before the SSID can be used?
- A. The wireless network interface must be assigned a Layer 3 address.
- B. The new network must be manually assigned to a FortiAP profile.
- C. The wireless network to Internet firewall policy must be configured.
- D. Security Fabric and HTTPS must be enabled on the wireless network interface.
Answer: A
Explanation:
Explanation
The wireless network interface must be assigned a Layer 3 address because it acts as the gateway for the tunnel mode SSID traffic. The FortiGate wireless controller uses this interface to communicate with the FortiAPs and the wireless clients. Without a valid IP address, the tunnel mode SSID cannot function properly.
References: Secure Wireless LAN Course Description, page 5; [FortiOS 6.4.0 Handbook - Wireless Controller], page 24.
NEW QUESTION # 17
Which administrative access method must be enabled on a FortiGate interface to allow APs to connect and function?
- A. Security Fabric
- B. SSH
- C. FortiTelemetry
- D. HTTPS
Answer: A
NEW QUESTION # 18
When configuring Auto TX Power control on an AP radio, which two statements best describe how the radio responds? (Choose two.)
- A. When the AP detects any wireless client signal weaker than -70 dBm, it will reduce its transmission power until it reaches the maximum configured TX power limit.
- B. When the AP detects PF Interference from an unknown source such as a cordless phone with a signal stronger that -70 dBm, it will increase its transmission power until it reaches the maximum configured TX power limit.
- C. When the AP detects any interference from a trusted neighboring AP stronger that -70 dBm, it will reduce its transmission power until it reaches the minimum configured TX power limit.
- D. When the AP detects any other wireless signal stronger that -70 dBm, it will reduce its transmission power until it reaches the minimum configured TX power limit.
Answer: C,D
Explanation:
Explanation
According to the web search results, Auto TX Power control is a feature that allows the AP to automatically adjust its transmission power based on the RF environment. The goal is to minimize interference and optimize coverage cells for roaming. When the AP detects any other wireless signal stronger than -70 dBm, it means that there is a potential source of interference nearby, so it will reduce its transmission power until it reaches the minimum configured TX power limit. This will reduce the interference and improve coexistence with other devices. When the AP detects any interference from a trusted neighboring AP stronger than -70 dBm, it means that there is a high density of APs in the area, so it will also reduce its transmission power until it reaches the minimum configured TX power limit. This will balance the load and avoid overlapping coverage areas.
References: AP Transmit Power and Enable Power Reduction with Auto TX, Transmit Power and Antenna Configuration, Meraki Auto RF: Wi-Fi Channel and Power Management
NEW QUESTION # 19
Six APs are located in a remotely based branch office and are managed by a centrally hosted FortiGate. Multiple wireless users frequently connect and roam between the APs in the remote office.
The network they connect to, is secured with WPA2-PSK. As currently configured, the WAN connection between the branch office and the centrally hosted FortiGate is unreliable.
Which configuration would enable the most reliable wireless connectivity for the remote clients?
- A. Configure a bridge mode wireless network and enable the Local authentication configuration option
- B. Install supported FortiAP and configure a bridge mode wireless network
- C. Configure a tunnel mode wireless network and enable split tunneling to the local network
- D. Configure a bridge mode wireless network and enable the Local standalone configuration option
Answer: C
NEW QUESTION # 20
Which two statements about background rogue scanning are correct? (Choose two.)
- A. When detecting rogue APs, a dedicated radio configured for background scanning can suppress the rogue AP
- B. Background rogue scanning requires DARRP to be enabled on the AP instance
- C. A dedicated radio configured for background scanning can support the connection of wireless clients
- D. A dedicated radio configured for background scanning can detect rogue devices on all other channels in its configured frequency band
Answer: B,D
NEW QUESTION # 21
Which two phases are part of the process to plan a wireless design project? (Choose two.)
- A. Hardware selection phase
- B. Installation phase
- C. Project information phase
- D. Site survey phase
Answer: C,D
NEW QUESTION # 22
Which two phases are part of the process to plan a wireless design project? (Choose two.)
- A. Hardware selection phase
- B. Installation phase
- C. Project information phase
- D. Site survey phase
Answer: C,D
Explanation:
Explanation
According to the web search results, the project information phase and the site survey phase are part of the process to plan a wireless design project. The project information phase involves defining the project scope, objectives, requirements, deliverables, and stakeholders. It also includes creating a project plan, a risk management plan, a communication plan, and a budget.1 The site survey phase involves conducting a physical inspection of the site where the wireless network will be deployed, measuring the signal strength and interference levels, identifying the optimal locations for the access points and antennas, and validating the network performance and coverage.2 The hardware selection phase and the installation phase are not part of the planning process, but rather part of the implementation process. The hardware selection phase involves choosing the appropriate wireless devices, such as access points, routers, switches, controllers, and cables, based on the network design and specifications.3 The installation phase involves installing, configuring, testing, and documenting the wireless network components according to the project plan and best practices.3 References: Wireless Device Network Planning and Design - Emerson, Telecommunications and Implementation Project Management - BICSI, Project Planning | Wireless Design Services | Digi International
NEW QUESTION # 23
Where in the controller interface can you find a wireless client's upstream and downstream link rates?
- A. On the controller CLI, using the diag wireless-controller wlac -d sta command
- B. On the AP CLI, using the cw_diag -d sta command
- C. On the AP CLI, using the cw_diag ksta command
- D. On the controller CLI, using the WiFi Client monitor
Answer: A
NEW QUESTION # 24
You are investigating a wireless performance issue and you are trying to audit the neighboring APs in the PF environment. You review the Rogue APs widget on the GUI but it is empty, despite the known presence of other APs.
Which configuration change will allow neighboring APs to be successfully detected?
- A. Enable Locate WiFi clients when not connected in the relevant AP profiles.
- B. Enable Monitor channel utilization on the relevant AP profiles.
- C. Ensure that all allowed channels are enabled for the AP radios.
- D. Enable Radio resource provisioning on the relevant AP profiles.
Answer: D
Explanation:
Explanation
The ARRP (Automatic Radio Resource Provisioning) profile improves upon DARRP (Distributed Automatic Radio Resource Provisioning) by allowing more factors to be considered to optimize channel selection among FortiAPs. DARRP uses the neighbor APs channels and signal strength collected from the background scan for channel selection.
NEW QUESTION # 25
As standard best practice, which configuration should be performed before configuring FortiAPs using a FortiGate wireless controller?
- A. Create a custom AP profile
- B. Set the wireless controller country setting
- C. Preauthorize APs
- D. Create wireless LAN specific policies
Answer: B
NEW QUESTION # 26
Which two statements about distributed automatic radio resource provisioning (DARRP) are correct? (Choose two.)
- A. DARRP requires that wireless intrusion detection (WIDS) be enabled to detect neighboring devices.
- B. DARRP measurements can be scheduled to occur at specific times.
- C. DARRP performs measurements of the number of BSSIDs and their signal strength (RSSI). The controller then uses this information to select the optimum channel for the AP.
- D. DARRP performs continuous spectrum analysis to detect sources of interference. It uses this information to allow the AP to select the optimum channel.
Answer: B,C
Explanation:
According to Fortinet training: "When using DARRP, the AP selects the best channel available to use based on the scan results of BSSID/receive signal strength (RSSI) to AC" and "To set the running time for DARRP optimization, use the following CLI command within the wireless controller setting: set darrp-optimize {integer}. Note that DARRP doesn't do continuous spectrum analysis..."
NEW QUESTION # 27
You are investigating a wireless performance issue and you are trying to audit the neighboring APs in the PF environment. You review the Rogue APs widget on the GUI but it is empty, despite the known presence of other APs.
Which configuration change will allow neighboring APs to be successfully detected?
- A. Enable Locate WiFi clients when not connected in the relevant AP profiles.
- B. Enable Monitor channel utilization on the relevant AP profiles.
- C. Ensure that all allowed channels are enabled for the AP radios.
- D. Enable Radio resource provisioning on the relevant AP profiles.
Answer: D
Explanation:
The ARRP (Automatic Radio Resource Provisioning) profile improves upon DARRP (Distributed Automatic Radio Resource Provisioning) by allowing more factors to be considered to optimize channel selection among FortiAPs. DARRP uses the neighbor APs channels and signal strength collected from the background scan for channel selection.
NEW QUESTION # 28
Refer to the exhibits.
Exhibit A
Exhibit B
Exhibit C
A wireless network has been installed in a small office building and is being used by a business to connect its wireless clients. The network is used for multiple purposes, including corporate access, guest access, and connecting point-of-sale and IoT devices.
Users connecting to the guest network located in the reception area are reporting slow performance. The network administrator is reviewing the information shown in the exhibits as part of the ongoing investigation of the problem. They show the profile used for the AP and the controller RF analysis output together with a screenshot of the GUI showing a summary of the AP and its neighboring APs.
To improve performance for the users connecting to the guest network in this area, which configuration change is most likely to improve performance?
- A. Enable frequency handoff on the AP to band steer clients
- B. Reduce the number of wireless networks being broadcast by the AP
- C. Install another AP in the reception area to improve available bandwidth
- D. Increase the transmission power of the AP radios
Answer: D
NEW QUESTION # 29
When using FortiPresence as a captive portal, which two types of public authentication services can be used to access guest Wi-Fi? (Choose two.)
- A. Short message service authentication
- B. Social networks authentication
- C. Hardware security token authentication
- D. Software security token authentication
Answer: A,B
NEW QUESTION # 30
Which two configurations are compatible for Wireless Single Sign-On (WSSO)? (Choose two.)
- A. A VAP configured for WPA2 or 3 Enterprise
- B. A VAP configured to authenticate locally on FortiGate
- C. A VAP configured to authenticate using a radius server
- D. A VAP configured for captive portal authentication
Answer: A,C
Explanation:
Explanation
In the SSID choose WPA2-Enterprise authentication.
WSSO is RADIUS-based authentication that passes the user's user group memberships to the FortiGate.
NEW QUESTION # 31
Which statement describes FortiPresence location map functionality?
- A. Provides real-time insight into user usage stats
- B. Provides real-time insight into user movements
- C. Provides real-time insight into user online activity
- D. Provides real-time insight into user purchase activity
Answer: B
Explanation:
Explanation
(Page 88 Study Guide) "FortiPresence provides data and analytics based on demographic segmentation and visitor movement between areas" According to the web search results, FortiPresence location map functionality provides real-time insight into user movements. It uses the location data from the Fortinet access points to detect each visitor's smartphone Wi-Fi signal and track their location and behavior within the site. It also provides data visualization in a customizable format, such as heat maps and animated flows, to show the visitor traffic and movement patterns.
This geographical data analysis can help improve visitor experiences and business outcomes.
References: Location Analytics | FortiPresence 22.4.0 - Fortinet Documentation, FortiPresence Data Sheet
NEW QUESTION # 32
A tunnel mode wireless network is configured on a FortiGate wireless controller.
Which task must be completed before the wireless network can be used?
- A. The wireless network interface must be assigned a Layer 3 address
- B. The wireless network to Internet firewall policy must be configured
- C. The new network must be manually assigned to a FortiAP profile.
- D. Security Fabric and HTTPS must be enabled on the wireless network interface
Answer: B
Explanation:
A FortiGate unit is an industry leading enterprise firewall. In addition to consolidating all the functions of a network firewall, IPS, anti-malware, VPN, WAN optimization, Web filtering, and application control in a single platform, FortiGate also has an integrated Wi-Fi controller.
NEW QUESTION # 33
Refer to the exhibits.
Exhibit A
Exhibit B
A wireless network has been created to support a group of users in a specific area of a building. The wireless network is configured but users are unable to connect to it. The exhibits show the relevant controller configuration for the APs and the wireless network.
Which two configuration changes will resolve the issue? (Choose two.)
- A. Increase the transmission power of the AP radio interfaces
- B. For both interfaces in the wtp-profile, configure set vaps to be "Authors"
- C. Disable intra-vap-privacy for the Authors vap-wireless network
- D. For both interfaces in the wtp-profile, configure vap-all to be manual
Answer: C,D
NEW QUESTION # 34
Which statement is correct about security profiles on FortiAP devices?
- A. Only bridge mode SSIDs can apply the security profiles
- B. Security profiles on FortiAP devices can use FortiGate subscription to inspect the traffic
- C. Disable DTLS on FortiAP
- D. FortiGate performs inspection the wireless traffic
Answer: A
NEW QUESTION # 35
As a network administrator, you are responsible for managing an enterprise secure wireless LAN. The controller is based in the United States, and you have been asked to deploy a number of managed APs in a remote office in Germany.
What is the correct way to ensure that the RF channels and transmission power limits are appropriately configured for the remote APs?
- A. Configure the APs individually by overriding the settings in Managed FortiAPs
- B. Configure the controller for the correct country code for Germany
- C. Create a new FortiAP profile and change the county code settings on the profile
- D. Clone a suitable FortiAP profile and change the county code settings on the profile
Answer: D
NEW QUESTION # 36
Refer to the exhibits.
Exhibit A
Exhibit B
The exhibits show the diagnose debug log of a station connection taken on the controller CLI.
Which security mode is used by the wireless connection?
- A. WPA2 Enterprise
- B. WPA2 Personal and radius MAC filtering
- C. WPA3 Enterprise
- D. Open, with radius MAC filtering
Answer: B
NEW QUESTION # 37
......
Fortinet NSE6_FWF-6.4 certification is an important credential for network security professionals who want to advance their careers in the field of secure wireless LAN technology. Fortinet NSE 6 - Secure Wireless LAN 6.4 certification program is recognized by employers around the world and is a valuable asset for anyone who wants to demonstrate their expertise in this area. In addition, earning the Fortinet NSE6_FWF-6.4 certification can lead to higher salaries, better job opportunities, and increased job security.
New NSE6_FWF-6.4 Test Materials & Valid NSE6_FWF-6.4 Test Engine: https://www.vceprep.com/NSE6_FWF-6.4-latest-vce-prep.html
NSE6_FWF-6.4 Updated Exam Dumps [2024] Practice Valid Exam Dumps Question: https://drive.google.com/open?id=1Hk5KaMnwGeMwe4huiLdVs378TMrwtYiK