Get New 2021 Valid Practice HPE Product Certified - OneView [2022] HPE2-T37 Q&A - Testing Engine
HPE2-T37 Dumps PDF - 100% Passing Guarantee
NEW QUESTION 17
For HPE Primera, match each task with the management tool that can be used to perform it.
Answer:
Explanation:
NEW QUESTION 18
A customer has to deploy 21 HPE Synergy Compute Modules in a boot from SAN setup. How this task can be simplified while keeping the profile consistent?
- A. Boot volumes can be prepared in advance and later presented as shared volumes to the Compute Modules.
- B. An existing volume can be replicated automatically when creating a server profile.
- C. Boot volumes can be created on demand and defined in the server profile template.
- D. single SAN volume can be created and utilized by all HPE Synergy Compute Modules.
Answer: C
NEW QUESTION 19
You configured downlink aggregation for one of the HPE Synergy Compute Modules in an environment by placing two connections in the same Link Aggregation Group. After you made the changes to the server profile, its status changed to critical.
What can be done to fix this issue?
- A. The teaming or bonding driver in the server OS must be configured to enable the LACP and to form the LAG correctly.
- B. Link Aggregation Group functionality should be enabled in advanced properties of the Logical Interconnect.
- C. The server profile for a given HPE Synergy compute module should be reapplied, then the Compute Module should be rebooted.
- D. Ensure that the Link Aggregation Group time-out value matches the server set values.
Answer: B
NEW QUESTION 20
Click the option that must be configured for an HPE OneView when an HPE storage system is connected directly to an HPE Synergy frame.
Answer:
Explanation:
NEW QUESTION 21
Refer to the exhibit.
Your customer created multiple networks in HPE OneView, but only Eth-1 is available to be used within a server profile. What is a likely cause of this situation?
- A. The other networks are not added to the Logical Interconnect Group configuration.
- B. The other networks are configured with a purpose other than General or Management.
- C. The other networks have Private Network' selected, which hides them from Compute Modules.
- D. The other networks are not configured with the required Smart Link parameter.
Answer: C
NEW QUESTION 22
Which parameters can be defined in a server profile template for HPE Synergy Compute Modules? (Select two.)
- A. partition layout for servers running Linux.
- B. IL0 IPv4 or IPv6 address.
- C. network and storage connectivity.
- D. NIC teaming setup at OS level.
- E. local storage and BIOS settings.
Answer: C,E
NEW QUESTION 23
Which statement about a Logical Enclosure for HPE BladeSystem is Hue?
- A. A logical enclosure must be created only for monitored HPE BladeSystem C700O enclosures.
- B. A logical enclosure can contain a mix of HPE BladeSystem c7000 and C3000 enclosures.
- C. A logical enclosure is created automatically, and it is always based on a single enclosure.
- D. A logical enclosure can have between 1 to 5 HPE BladeSystem c7000 enclosures.
Answer: C
NEW QUESTION 24
Your customer plans to use HPE OneView to manage a small environment based on HPE ProLiant servers that includes G7 and Gen 10 systems. What should you explain to this customer?
- A. HPE ProLiant G7 and Gen10 cannot be managed using the same appliance.
- B. HPE Management Agent must he installed for for HPE ProLiant Gen 10 servers.
- C. HPE ProLiant Gen 10 servers do not need an HPE OneView license.
- D. Not all of the features will be available for HPE ProLiant G7 systems.
Answer: C
NEW QUESTION 25
How can your customer implement HPE OneView so that it can be used to manage an HPE ProLiant server and HPE BladeSystem?
- A. As an application running on the server with Windows system.
- B. As an application running on the server with CentOS Linux system
- C. As a virtual appliance running on the supported hypervisor.
- D. As a physical appliance based on HPE ProLiant 360 Gen 10.
Answer: D
NEW QUESTION 26
Refer to the exhibit.
After adding SAN Manager to HPE OneView. you noticed that all SANs are in the discovered state. How will this affect HPE OneView storage management capabilities?
- A. Auto-zoning functionality will not work until SANs are associated with networks.
- B. Volume presentation through server profile will work with the discovered state.
- C. Snapshot functionality will be limited only to the volumes not using these SANs.
- D. Volume provisioning will only work for arrays that ate accessible through these SANs.
Answer: B
NEW QUESTION 27
Which statement about RoCE network restrictions is true?
- A. RoCE networks cannot be configured when Virtual Connect modules are used.
- B. RoCE networks require Virtual Connect SE 32Gb FC Modules.
- C. RoCE networks are not supported with HPE BladeSystem
- D. RoCE networks are supported only when PVLANs are enabled.
Answer: C
NEW QUESTION 28
What is required to add remote frame link topology to HPE OneView?
- A. Multi-site licenses must be added to HPE OneView and activate for all available HPE Synergy frames.
- B. The IP address assigned to HPE Composer installed in a remote site must be registered in a primary site.
- C. The HPE OneView certificate from the primary site must be added to HPE OneView in the remote site.
- D. Management ports of the remote frame link topology must be connected to the management LAN.
Answer: A
NEW QUESTION 29
Which statement about a server profile for an Apollo system is true?
- A. Virtual WWNs and MAC addresses can be defined
- B. UEFI optimized is the only available boot mode
- C. Fibre Channel connections can be defined
- D. Enclosure Group Is automatically selected
Answer: A
NEW QUESTION 30
Click the option from the HPE OneView main menu that will allow you to define UPS or other components that will work as a placeholder in a rack system.
Answer:
Explanation:
NEW QUESTION 31
You want to add the latest IL0 firmware to an HPE OneView firmware repository. How can you complete this task?
- A. An external repository must be created, because standalone components are supported only In an external repository.
- B. A custom SPP iso Image must be created with the new IL0 firmware version and uploaded to the repository.
- C. ILO firmware can be marked as a hotnx and uploaded directly to the Internal or external firmware repository.
- D. A PowerShell script must be used to upload IL0 firmware to the Internal or external firmware repository.
Answer: A
NEW QUESTION 32
......
HPE2-T37 Braindumps Real Exam Updated on Nov 20, 2021 with 41 Questions: https://www.vceprep.com/HPE2-T37-latest-vce-prep.html
Latest HPE2-T37 PDF Dumps & Real Tests Free Updated Today: https://drive.google.com/open?id=1ni3E8v4-uYKoTz7Jmpu84X1n25OimW6f