[Nov-2021 Newly Released] HPE2-T37 Dumps for HPE Product Certified - OneView [2022] Certified
Updated Verified HPE2-T37 dumps Q&As - 100% Pass
NEW QUESTION 23
Which statement about M-LAG setup is true?
- A. sFLOW cannot be enabled if M-LAG is configured between HPE Synergy Virtual Connect modules in the same frame.
- B. M-LAG has to be defined manually for HPE BladeSystem, but it is automatically configured for HPE Synergy.
- C. M-LAG for HPE Synergy can be either single-homed or multi-homed, while for HPE BladeSystem only single-homed.
- D. When combined with IRF, M-LAG will allow you to aggregate ports coming from clustered HPE Synergy Virtual Connect modules.
Answer: D
NEW QUESTION 24
Which statement about an HPE OneView server profile is true?
- A. A server profile can be created only for HPE BladeSystem, HPE Synergy, and HPE Superdome Flex servers.
- B. A server profile can be used to update firmware and drivers when the operating system on the server is up and running.
- C. A server profile created for a specific server hardware type cannot be moved to a server with a different server hardware type.
- D. A server profile can be used to configure a local storage controller, but cannot be used to configure SAN-based storage.
Answer: D
NEW QUESTION 25
After replacing a failed Compute Module, you notice the server profile Is not automatically assigned to the replaced server hardware. What can cause this issue?
- A. The enclosure group has to be updated to match the original enclosure group.
- B. The replacement server has more memory or CPUs than broken machine.
- C. Server profile affinity is configured to Device Day + server hardware.
- D. IL0 firmware of the replacement server is different than firmware in broken server.
Answer: D
NEW QUESTION 26
Refer to the exhibit.
After adding SAN Manager to HPE OneView. you noticed that all SANs are in the discovered state. How will this affect HPE OneView storage management capabilities?
- A. Auto-zoning functionality will not work until SANs are associated with networks.
- B. Snapshot functionality will be limited only to the volumes not using these SANs.
- C. Volume presentation through server profile will work with the discovered state.
- D. Volume provisioning will only work for arrays that ate accessible through these SANs.
Answer: C
NEW QUESTION 27
You want to put two FlexNlCs into a single Link Aggregation Group within a server profile. What Is a prerequisite for this setup?
- A. The Compute Module profile must have exactly two connections defined.
- B. The sFlow option must be enabled and configured.
- C. An upgrade license must be purchased and deployed.
- D. Both FlexNlCs must be connected to the same network.
Answer: B
NEW QUESTION 28
Refer to the exhibit.
A customer complains that firmware compliance is empty. The customer confirmed that Synergy Service Pack is uploaded to the HPE OneView repository. How should you respond?
- A. All of the components are up to date and compliant with firmware baseline.
- B. The firmware repository is not defined within firmware compliance report.
- C. The refresh procedure must be performed on each logical enclosure to refresh firmware.
- D. The firmware repository service must be restarted using maintenance connection.
Answer: D
NEW QUESTION 29
You ate implementing an HPE Synergy solution with multiple frames in one management ring. Image Streamer is not a part of this solution. How can an IPv4 address pool defined by the administrator be used In HPE OneView?
- A. to provide static IP addresses for an operating system running on a Compute Module
- B. to provide static IP addresses for Logical Interconnects and Logical Enclosures
- C. to provide static IP addresses to IL0 and interconnect modules if applicable
- D. to provide static IP addresses for storage systems managed in HPE OneView
Answer: A
NEW QUESTION 30
Refer to the exhibit.
You discovered that one of the profiles is not compliant with the server profile template. What could cause this profile to be inconsistent with the server profile template?
- A. Changes to the server profile were implemented directly on the server profile.
- B. The server was powered off or rebooted recently and IL0 did not reconnect to HPE OneView.
- C. HPE OneView was restored from a backup that created ^consistency with the server profile template.
- D. Network connectivity for HPE Synergy Compute Module was changed outside HPE OneView.
Answer: D
NEW QUESTION 31
Your customer asks you if it is possible to perform HPE Synergy initial setup remotely. How should you respond?
- A. HPE Synergy cannot be deployed remotely, as Initial setup must be performed using a local console connection.
- B. HPE Synergy can be configured remotely through a secure connection to the FLM if this option was enabled In the factory.
- C. Remote HPE Synergy Installation can be done only if an additional set of the services was purchased together with hardware platform.
- D. Remote HPE Synergy setup is possible if HPE Composer 2 is used and a DHCP server Is available in the management network.
Answer: B
NEW QUESTION 32
Which HPE components can be managed using HPE Composer? (select two.)
- A. HPE Synergy 480 Compute Modules
- B. HPE Synergy Virtual Connect SE 32Gb FC Module
- C. HPE B-series SN6600B Fibre Channel Switch
- D. HPE MSA 2062 Storage Array
- E. HPE Superdome Flex 280
Answer: B,C
NEW QUESTION 33
Refer to the exhibit.
Your customer created multiple networks in HPE OneView, but only Eth-1 is available to be used within a server profile. What is a likely cause of this situation?
- A. The other networks are configured with a purpose other than General or Management.
- B. The other networks are not added to the Logical Interconnect Group configuration.
- C. The other networks are not configured with the required Smart Link parameter.
- D. The other networks have Private Network' selected, which hides them from Compute Modules.
Answer: D
NEW QUESTION 34
You want to update the firmware for only two HPE Synergy Virtual Connect SE 32Gb FC Modules of a large environment. From which level must this procedure be initiated?
- A. Logical Enclosure
- B. Server Profile
- C. Logical Interconnect
- D. Logical Interconnect Group
Answer: A
NEW QUESTION 35
Refer to the exhibit.
Your customer wants to define a Logical Interconnect Group (UG) and set the redundancy of the master modules to highly available, but this option is not available. What is a possible reason?
- A. Some master modules only support a redundant setup.
- B. There are not sufficient frames for highly available setup.
- C. A dedicated license must be added to HPE OneView to enable this feature.
- D. Firmware on the master modules is too low to support highly available setup.
Answer: A
NEW QUESTION 36
A customer has to deploy 21 HPE Synergy Compute Modules in a boot from SAN setup. How this task can be simplified while keeping the profile consistent?
- A. An existing volume can be replicated automatically when creating a server profile.
- B. Boot volumes can be created on demand and defined in the server profile template.
- C. single SAN volume can be created and utilized by all HPE Synergy Compute Modules.
- D. Boot volumes can be prepared in advance and later presented as shared volumes to the Compute Modules.
Answer: B
NEW QUESTION 37
You configured downlink aggregation for one of the HPE Synergy Compute Modules in an environment by placing two connections in the same Link Aggregation Group. After you made the changes to the server profile, its status changed to critical.
What can be done to fix this issue?
- A. The teaming or bonding driver in the server OS must be configured to enable the LACP and to form the LAG correctly.
- B. The server profile for a given HPE Synergy compute module should be reapplied, then the Compute Module should be rebooted.
- C. Ensure that the Link Aggregation Group time-out value matches the server set values.
- D. Link Aggregation Group functionality should be enabled in advanced properties of the Logical Interconnect.
Answer: D
NEW QUESTION 38
Refer to the exhibit.
Which statement about the logical interconnect shown is true?
- A. FC uplinks are not supported and will be converted to FCoE or RoCE uplinks.
- B. For FC uplink sets, an additional uplink from second module should be added for redundancy.
- C. Additional uplink ports can be added to ETH-Uplink to increase available bandwidth.
- D. The maximum supported number of the internal networks for logical interconnect is configured.
Answer: A
NEW QUESTION 39
......
Latest HPE2-T37 Exam Dumps HP Exam from Training: https://www.vceprep.com/HPE2-T37-latest-vce-prep.html
New 2021 Latest Questions HPE2-T37 Dumps - Use Updated HP Exam: https://drive.google.com/open?id=1PdZnE73mi0slWWMXYtFMDP__xBCYIfNc